Powerdebugger = Atmel PowerDebugger (ARM/AVR) in JTAG mode Ponyser = design ponyprog serial, reset=!txd sck=rts mosi=dtr miso=cts
#ATMEL DRAGON BOOTLOADER SERIAL#
Pavr = Jason Kyle's pAVR Serial Programmer
O-link = O-Link, OpenJTAG from openmoko = Openmoko debug board (v3) Mib510 = Crossbow MIB510 programming board Lm3s811 = Luminary Micro LM3S811 Eval Board (Rev. Linuxspi = Use Linux SPI device in /dev/spidev* JtagmkII_avr32 = Atmel JTAG ICE mkII im AVR32 mode Jtagkey = Amontec JTAGKey, JTAGKey-Tiny and JTAGKey2 Jtag3pdi = Atmel AVR JTAGICE3 in PDI mode Jtag3isp = Atmel AVR JTAGICE3 in ISP mode Jtag3dw = Atmel AVR JTAGICE3 in debugWIRE mode Jtag2isp = Atmel JTAG ICE mkII in ISP mode
Jtag2dw = Atmel JTAG ICE mkII in debugWire mode Jtag2avr32 = Atmel JTAG ICE mkII im AVR32 mode 0450 (474 KB/s) - ‘bloader.hex’ saved $ sudo nano $ cd $ sudo nano $ $ sudo nano $ sudo nano $ avrdude -c pi_isp -p m328p -e -U flashbloader.hex:i -U lfusem -U hfusem -U efusem -U lockmĪvrdude: Can't find programmer id "pi_isp"Ģ232HIO = FT2232H based generic programmerĪrduino-ft232r = Arduino: FT232R connected to ISPĪtmelice = Atmel-ICE (ARM/AVR) in JTAG modeĪtmelice_dw = Atmel-ICE (ARM/AVR) in debugWIRE modeĪtmelice_isp = Atmel-ICE (ARM/AVR) in ISP modeĪtmelice_pdi = Atmel-ICE (ARM/AVR) in PDI modeĪtmelice_updi = Atmel-ICE (ARM/AVR) in UPDI modeĪvr109 = Atmel AppNote AVR109 Boot LoaderĪvr910 = Atmel Low Cost Serial ProgrammerĪvrftdi = FT2232D based generic programmerīuspirate_bb = The Bus Pirate (bitbang interface, supports TPI)īutterfly = Atmel Butterfly Development Boardīwmega = BitWizard ftdi_atmega builtin programmerĬ232HM = FT232H based module from FTDI and Ĭ2n232i = serial port banging, reset=dtr sck=!rts mosi=!txd miso=!ctsĭasa = serial port banging, reset=rts sck=dtr mosi=txd miso=ctsĭasa3 = serial port banging, reset=!dtr sck=rts mosi=txd miso=ctsĭragon_dw = Atmel AVR Dragon in debugWire modeĭragon_hvsp = Atmel AVR Dragon in HVSP modeĭragon_isp = Atmel AVR Dragon in ISP modeĭragon_jtag = Atmel AVR Dragon in JTAG modeĭragon_pdi = Atmel AVR Dragon in PDI modeĮhajo-isp = avr-isp-programmer from eHaJo, įlip1 = FLIP USB DFU protocol version 1 (doc7618)įlip2 = FLIP USB DFU protocol version 2 (AVR4023) My screen from bootloader flash and clip of log file conf.still makes no sense and does not workĪlso if we only solder a pin to one part of the reset switch pad do we need to push the reset switch while flashing? to connect both pads or is it just a common pad and the illustration is adding extra?Ĭurious what is going on here but to me it seems waterott is not flashing bootloaders to the board like the are supposed to do we create that or is it in a specific directory we must enter to add the pinouts to because i get a blank screen when using the commands provided and saved a file with the contents in it as. conf file we edit before flashing the boot loader. Or do we remove them and then flash firmware
Sudo reboot and remove the wires before rebooting or do we just flash the firmware right after while the wires are still attached ? Now some unclear things about the directions for people without electronics degreesįlashing the bootloader should be done with the pins as per the diagram , However it will not flash (pi_isp does not exist is the error i get and a list of available bootflashers) (avrdude -c pi_isp -p m328p -e -U flashbloader.hex:i -U lfusem -U hfusem -U efusem -U lockm)
#ATMEL DRAGON BOOTLOADER DOWNLOAD#
I suspect watterott is NOT FLASHING THE BOOTLOADERĪfter chasing down all the dead links provided i finally got the hex to download
JustinB Mario i have the same issue with this hat 2 of them actually
0 kommentar(er)
